The Best Putty and Gap Fillers for Miniatures
Filler is the step between sanding and priming that nobody tells beginners about. Buy the wrong one and you spend an evening sanding something that will not sand.

The short answer
Buy Green Stuff if you want one putty that fills gaps and sculpts, and Milliput Superfine White if you want a filler you can sand genuinely flush. For a Gunpla seam specifically, Mr. Dissolved Putty or Tamiya Basic Type putty is faster than either, because there is no mixing and nothing to knead.
The quick version
| # | Product | Best for | Score | Price |
|---|---|---|---|---|
| 1 | ![]() Milliput Superfine White Two-Part Epoxy Putty (113.4 g)The one epoxy putty on this page that sands like plastic. Cold-setting, non-shrinking and rock hard when cured, which is exactly what a Gunpla seam or a resin join needs. | Best overall filler | 9.2 | Check price on Amazon |
| 2 | ![]() Green Stuff (Kneadatite Blue/Yellow) Epoxy Putty TapeThe hobby default, and deservedly so: knead the blue and yellow strips together and you get a tacky putty you can push into a gap with a wet tool. Cures flexible, which is both its strength and its limit. | Best if you also want to sculpt | 8.6 | Check price on Amazon |
| 3 | ![]() Tamiya Putty (Basic Type) 32 g — 87053Gray solvent putty in a tube. Squeeze it onto a seam, let it flash off, sand it back. Tamiya says plainly that it is not for large gaps, and believing them saves you a redo. | Best one-part putty for seams | 8.8 | Check price on Amazon |
| 4 | ![]() Mr. Hobby Mr. Dissolved Putty (P119), 40 mlA thick lacquer putty used straight from the jar with a toothpick or an old brush. It bites into styrene and fills a sink mark or a pinhole in one pass, which is why Gunpla builders keep a jar. | Best for Gunpla seams and sink marks | 8.5 | Check price on Amazon |
| 5 | ![]() Deluxe Materials Perfect Plastic Putty (BD-44), 40 mlA superfine one-part water-based filler that handles deeper cavities than most acrylic putties and wipes back with a damp cotton bud before it sets. Low odor, water cleanup, takes paint. | Best water-based filler | 8.7 | Check price on Amazon |
| 6 | ![]() Vallejo Plastic Putty (70.400), 17 mlA water-based filler in a dropper bottle that you brush or spatula into a gap and clean up with water. Dries white, opaque and sandable, with none of the solvent smell. | Best filler for a shared desk | 8.2 | Check price on Amazon |
| 7 | ![]() Aves Apoxie Sculpt (1/4 lb, two-part)A two-part epoxy clay with a two-to-three hour working window that smooths with water and cures hard with no shrinkage. The right buy when you are building something rather than filling a line. | Best for structural repairs | 8.4 | Check price on Amazon |
| 8 | ![]() Citadel Liquid Green Stuff (12 ml)Brush-on acrylic filler in a Citadel pot. Fine on a mold line or a hairline gap, oversold for anything else, and the name misleads — it is not Green Stuff and it does not sculpt. | Mold lines only | 6.8 | Check price on Amazon |
| 9 | ![]() Cyanoacrylate gel (super glue, gel formula)The glue for everything solvent cement cannot touch. The gel formula is the one to buy: it stays where you put it instead of running into detail. | The free filler you already own | 8.7 | Check price on Amazon |
Scores are our own editorial read against the criteria stated below — not a lab measurement and not a user rating. Tap a row for the full write-up.
What we judged these on
“Putty” is one word covering four unrelated products, which is the whole reason this purchase goes wrong. A two-part epoxy and a brush-on acrylic filler are not competing for the same job, and a page that ranks them on one axis is lying to you. So every pick below is scored on four:
- Fills a seam. Does it stay in the gap, and does it still fill the gap once it is dry? Anything with a solvent or water in it shrinks back as that carrier leaves. Epoxies do not.
- Sands flush. The one that separates the field. Some of these powder away under 600 grit and leave a surface you cannot find with a fingernail. One of them tears like an eraser and cannot be sanded at all.
- Sculpts. Can you build a shape with it — a cloak, a hood, a gap in a conversion where there is no part at all? Only the kneadable epoxies can.
- Shelf life. The cost nobody counts. Half these products are mostly dead eighteen months after opening, and the cheap big pack is not cheap if you throw two thirds of it away.
Scores are our own editorial read against those four criteria, not a lab measurement, and we have no testing rig to claim otherwise. Specs come from the makers’ own listings and from live retailer pages, both cited at the bottom of the page.
The four types, and which gap each one is for
Before any brand name, work out which of these four you are buying. It decides the outcome far more than which company made it.
1. Two-part kneadable epoxy
Green Stuff, Milliput, Apoxie Sculpt. You cut equal amounts of two components, knead them until the color is uniform, and push the result into the gap. No solvent and no water, so nothing shrinks: what you pack in is what is there tomorrow. These are the only fillers that can also add material — a shoulder pad that does not exist, a hood, a repaired banner.
The trade is working time and mess. You have minutes to an hour depending on the product, the stuff is tacky until it starts to set, and every tool you touch it with needs to be wet.
2. One-part solvent putty
Tamiya Basic Type, Mr. Dissolved Putty, Mr. Surfacer 500 at the thin end. Pigment and binder carried in a solvent that partially melts the plastic it touches, so the filler keys into the part rather than just sitting on it. Squeeze it on, wait, sand back.
These are the fastest fillers for a plain seam — no mixing, no ratio, no waste — and they sand superbly. They also shrink as the solvent leaves, which is why a deep fill done in one pass always sinks into a shallow trench a day later.
3. One-part water-based filler
Vallejo Plastic Putty, Deluxe Materials Perfect Plastic Putty, Citadel Liquid Green Stuff. Acrylic filler thinned with water. Brush it in, wipe the excess with a damp cotton bud, sand lightly if anything is left. No smell, no ventilation question, no solvent anywhere near your paints.
They shrink the most of any type and they are the weakest, so they belong on mold lines, hairline gaps and pinholes — not on a structural join and not in a 2 mm trench.
4. Cyanoacrylate, with or without filler powder
Super glue gel is a filler and most people never notice. A drop of gel in a gap, a dusting of baking soda or talc on top, and it cures instantly into a hard mass that sands like plastic. It is the fastest fix on this page by a mile and the least pleasant to get right.
If you are here for a Gunpla seam
Nearly everyone searching for model putty is looking at one of two things: a visible seam line down the middle of a snap-fit part, or a sink mark where the plastic cooled unevenly. Both want a one-part putty, not an epoxy.
The sequence that works: glue the seam shut with a thin solvent cement and squeeze the halves until a bead of melted plastic rises out of the join. Let it harden for a day, then sand that bead back — on a good day the seam is gone and no putty was needed at all. Putty is for what is left: the short section where the fit was poor, the pinhole, the sink mark.
For that remainder, Mr. Dissolved Putty is the Gunpla builder’s default and Tamiya Basic Type is the cheaper, easier-sanding alternative. Both need the surface sanded and then primed, because filler under paint always reads differently to bare plastic — see the primer roundup for what to put over it, and how to remove nub marks for the sanding technique this step assumes.
One warning specific to pre-colored kits: filler plus sanding destroys the molded surface finish, which means that section now has to be painted. Filling one seam on an otherwise unpainted kit often looks worse than the seam did. Decide whether the kit is getting painted before you open a tube.
If you are here for a miniature
Different problem entirely. On a plastic wargaming model the gaps are torso-to-leg joins, shoulder-to-arm joins and mold lines, and the model gets handled, dropped and put in a foam tray every week.
That handling is the argument for Green Stuff. It cures flexible, so a filled shoulder joint on a model that gets picked up a hundred times does not crack along the fill line the way a hard filler eventually does. It is also the only option when the “gap” is really a missing shape — a conversion where two kits do not meet, a cloak that needs to continue.
The thing nobody warns you about: Green Stuff does not sand. Cured, it is rubbery, and 400 grit tears at it instead of cutting it. Everything you want from the finished surface has to be achieved while the putty is still soft, with a wet tool or a wet fingertip. If you need to sand a fill flush on a miniature, that is Milliput’s job, and keeping both on the desk is the normal answer rather than a luxury.
Mold lines on their own do not need putty at all — they need scraping off with the back of a blade, which the beginner mistakes guide covers. Filler on a mold line is usually a sign the line was sanded into a dip rather than scraped flat.
Shrinkage: the thing that makes you redo the work
This is the single most useful idea on the page. Any filler that contains a carrier — solvent, water, alcohol — loses volume when that carrier evaporates. A gap you filled perfectly flush at 9 pm is a shallow dish at 9 am.
So with solvent and water-based putties, you deliberately overfill, let it fully cure, and sand back to the surface. Two thin applications beat one thick one every time: a thick one skins over on the outside while the inside is still wet, and sinks for a week.
Epoxies do not do this, which is why they win the deep-gap case outright. A 2 mm trench between two badly fitting resin halves is an epoxy job. The same trench filled with brush-on acrylic filler will take five coats and still move.
What decides price
Pack size and brand, not performance. The cheapest thing on this page per gram is Milliput, a product aimed at ceramic repair that happens to be the best sanding filler most modelers ever use. The most expensive per milliliter is Citadel Liquid Green Stuff, which is a competent acrylic filler in a 12 ml pot with a Games Workshop label.
We do not print prices on this site, because a number that is three weeks old is worse than no number — every buy link here goes to a live listing so you see the real current price. What we can tell you is the shape of the decision: all of these are inexpensive in absolute terms, nothing on this page will change your hobby budget, and the waste is what costs you. An opened epoxy pack has a clock on it. A 1/4 lb tub of Apoxie Sculpt is a lifetime supply for someone filling shoulder joints, and most of it will go hard in the tub.
Which is the real buying advice: buy the smallest pack of the right type, not the biggest pack of the cheapest one. The exception is Milliput, where the standard 113.4 g carton is the only size most retailers stock and is cheap anyway.
Storage, because this is where the money goes
Two-part epoxies cure by contact, slowly, even inside the pack. The Green Stuff tapes sold “with gap” exist precisely because the two strips touching each other along their whole length is what turns an unopened pack into a green brick. Pay the small premium for the gapped version, or cut the tape into sections and separate the halves yourself.
Solvent putties skin over in the tube. Wipe the thread, cap it hard, store it upright. Once the tube has a skin, you can usually still dig underneath it, but the day it goes rubbery it is finished.
Water-based fillers dry out through the lid and are the shortest-lived of the lot. A pot of brush-on filler that has gone stringy can sometimes be rescued with a drop or two of water and a long stir — the same trick that works on dried-out paint, and with the same caveat: it restores the consistency, not the performance.
The tools that matter more than the putty
Filler is applied with something, and the something is usually wrong. Three cheap things change the result more than switching brands:
- Water. A pot of water and a brush, used to wet every tool and fingertip that touches an epoxy. Dry tools drag the putty out of the gap; wet tools smooth it in. This is the entire difference between a neat fill and a mess.
- A clay shaper or an old brush with the bristles cut short. A stiff silicone tip pushes putty where a metal sculpting tool just lifts it.
- Sanding sticks in two grits. Filler is only as good as the sanding that follows it — the sanding stick picks cover which grits actually matter.
And one that costs nothing: a cocktail stick. For solvent and water-based putties, a toothpick is a better applicator than any brush, because you are placing a tiny amount in a specific place rather than painting an area.
Safety, briefly and honestly
Epoxy putties are skin sensitizers. Most people knead Green Stuff bare-handed for years with no trouble and some develop a contact allergy that does not go away; nitrile gloves cost pennies and the decision is yours. Wash your hands before you eat, every time.
Solvent putties and the lacquer-based liquids need the same ventilation as any solvent product in this hobby. If you already airbrush, you have the setup — the spray booth guide and the respirator picks cover it. If you do not, open a window and do not work with a solvent putty for an hour in a closed room.
Super glue plus baking soda releases real heat as it cures. On a small fill you will not notice; on a large one you can warp a thin plastic part. Build it up in stages.
The verdict
If you buy one thing: Milliput Superfine White. It fills, it does not shrink, it sands genuinely flush, and the pack costs about what one hobby-branded 12 ml pot does. Its weakness is that it cures hard and does not flex.
If you buy two: add Green Stuff. Between them you have a filler that sands and a filler that sculpts and flexes, which is the complete answer for miniatures and conversions.
If you only build Gunpla: skip both and buy Mr. Dissolved Putty or Tamiya Basic Type. Seams and sink marks are one-part-putty problems, and the mixing step is pure overhead you would never use.
If you share the room: Vallejo Plastic Putty or Perfect Plastic Putty. Water cleanup, no smell, no argument with anyone else in the house.
Next steps from here: the tools that create the gaps you are filling are in the beginner tool picks, and if your gap is actually a weak joint on a metal or resin model, the fix is mechanical rather than cosmetic — see pin vises, magnets and pinning.
The picks in full
Milliput Superfine White Two-Part Epoxy Putty (113.4 g)
The one epoxy putty on this page that sands like plastic. Cold-setting, non-shrinking and rock hard when cured, which is exactly what a Gunpla seam or a resin join needs.
What it gets right
- Sands and files to a genuinely flush, feather-edged finish — the reason modelers keep it beside the Green Stuff
- Smooths with a wet finger or brush while workable, so you can often avoid sanding altogether
- The pack is large and cheap per gram compared with hobby-branded fillers
Who it is wrong for
- Cures hard and slightly brittle, so it is the wrong choice on a thin flexing part
- Both sticks are nearly the same off-white, so under-mixing is easy and leaves soft patches that never cure
- Five minutes of kneading per batch is real work, and the pack is far more than a miniature painter will ever use
Scored against this page’s criteria
Specs from the manufacturer: Milliput product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Green Stuff (Kneadatite Blue/Yellow) Epoxy Putty Tape
The hobby default, and deservedly so: knead the blue and yellow strips together and you get a tacky putty you can push into a gap with a wet tool. Cures flexible, which is both its strength and its limit.
What it gets right
- Sculptable: it holds a shape, takes a texture and blends into surrounding detail with a wet tool
- Cures flexible rather than brittle, so a filled joint on a model that gets handled does not crack out
- You mix only what you need, so a pack lasts years if the halves are stored apart
Who it is wrong for
- Sands badly — cured Green Stuff is rubbery and tears rather than powdering, so get it right wet
- Tacky while workable; it sticks to dry fingers and tools, and water is the only fix
- The “with gap” tapes cost more but are the only versions that do not slowly cure in the pack
Scored against this page’s criteria
Specs from the manufacturer: The Army Painter product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Tamiya Putty (Basic Type) 32 g — 87053
Gray solvent putty in a tube. Squeeze it onto a seam, let it flash off, sand it back. Tamiya says plainly that it is not for large gaps, and believing them saves you a redo.
What it gets right
- No mixing, no ratios, no waste — the lowest-effort filler for a hairline seam
- Sands beautifully and feathers into the surrounding plastic
- Thins with lacquer thinner into a brushable slurry for scratches and pinholes
Who it is wrong for
- It shrinks as the solvent leaves, so a deep fill sinks and needs a second pass
- Solvent-based: it bites into styrene, and a heavy application can soften fine detail
- Needs ventilation and a lid kept on, or the tube skins over
Scored against this page’s criteria
Specs from the manufacturer: Tamiya product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Mr. Hobby Mr. Dissolved Putty (P119), 40 ml
A thick lacquer putty used straight from the jar with a toothpick or an old brush. It bites into styrene and fills a sink mark or a pinhole in one pass, which is why Gunpla builders keep a jar.
What it gets right
- Thick enough to stay in a seam, thin enough to flow into a pinhole — the gap between a putty and a surfacer
- Modelers report it needs fewer passes than Mr. Surfacer 500 on a deep seam, because it sinks back less
- No mixing and no waste: dip, apply, close the jar
Who it is wrong for
- Lacquer-based, so it needs ventilation and will attack bare styrene if you flood it
- Harder to sand cleanly than Tamiya's basic putty — wipe the excess off while wet instead
- Stir it from the bottom before use or the first application is mostly thinner
Scored against this page’s criteria
Specs from the manufacturer: Mr. Hobby product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Deluxe Materials Perfect Plastic Putty (BD-44), 40 ml
A superfine one-part water-based filler that handles deeper cavities than most acrylic putties and wipes back with a damp cotton bud before it sets. Low odor, water cleanup, takes paint.
What it gets right
- The damp-cotton-bud trick removes the excess before it cures, which often eliminates sanding entirely
- Handles deeper cavities than a thin acrylic filler without slumping out of the gap
- Takes primer and paint readily and does not fight an acrylic topcoat
Who it is wrong for
- Like every water-based filler it shrinks slightly — build deep fills in layers
- Not a structural filler; it will not hold a joint together
- Stock is patchy at US hobby retailers, so it is usually an order rather than a shelf buy
Scored against this page’s criteria
Specs from the manufacturer: Deluxe Materials product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Vallejo Plastic Putty (70.400), 17 ml
A water-based filler in a dropper bottle that you brush or spatula into a gap and clean up with water. Dries white, opaque and sandable, with none of the solvent smell.
What it gets right
- No solvent and no respirator question — usable at a desk in a shared room
- The dropper bottle meters out tiny amounts, which is most hobby filling
- Water cleanup means a wet brush shapes the fill and leaves nothing to sand
Who it is wrong for
- Water-based fillers shrink as they dry; deep gaps want two or three thin passes
- Weaker than an epoxy — it fills, it does not structurally join
- Dries white, so it reads loudly through a thin topcoat if you forget to prime over it
Scored against this page’s criteria
Specs from the manufacturer: Vallejo product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Aves Apoxie Sculpt (1/4 lb, two-part)
A two-part epoxy clay with a two-to-three hour working window that smooths with water and cures hard with no shrinkage. The right buy when you are building something rather than filling a line.
What it gets right
- Hours of working time instead of minutes, so you can sculpt a cloak or a base without racing the putty
- Smooths to a glassy finish with a wet tool, which removes most of the sanding a hard filler would need
- Waterproof and genuinely strong once cured — it repairs a snapped resin part rather than just hiding the join
Who it is wrong for
- Overkill for a seam; mixing a batch to fill a mold line wastes most of it
- Sticky to the point of frustration before it starts to set — wet tools, or it goes everywhere
- A 1/4 lb pack is a lifetime supply for a miniature painter, and the clock starts once it is opened
Scored against this page’s criteria
Specs from the manufacturer: Aves product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Citadel Liquid Green Stuff (12 ml)
Brush-on acrylic filler in a Citadel pot. Fine on a mold line or a hairline gap, oversold for anything else, and the name misleads — it is not Green Stuff and it does not sculpt.
What it gets right
- Brushes straight into a mold line with no mixing, which is the filling job most painters actually have
- Water cleanup, no smell, safe to use beside paints at the same desk
- Sold wherever Citadel paint is, so it is the one filler you can buy on a Saturday afternoon
Who it is wrong for
- It shrinks noticeably, so a real gap takes three or four coats and can still sink
- The most expensive filler here per milliliter by a wide margin
- Stock is intermittent at US retailers, and nothing about it justifies waiting
Scored against this page’s criteria
Specs from the manufacturer: Citadel product page

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
Cyanoacrylate gel (super glue, gel formula)
The glue for everything solvent cement cannot touch. The gel formula is the one to buy: it stays where you put it instead of running into detail.
What it gets right
- Bonds resin and metal, which is most of what a solvent cement will refuse
- Gel does not wick into recesses and ruin the detail around the joint
- Doubles as a gap filler, especially with a dusting of baking soda
Who it is wrong for
- A brittle bond — it shears under stress where a solvent weld would flex
- Fogs clear parts and leaves a white bloom on dark surfaces
- Glues fingers to models with total reliability
Scored against this page’s criteria

We do not publish prices. Amazon shows the current one, which is the only one that is ever right. #ad · how this is funded
FAQ
Questions people actually ask
What is the best gap filler for miniatures?
Green Stuff or Milliput — which should I buy?
Does model putty shrink?
How do I fill a Gunpla seam?
Is Citadel Liquid Green Stuff the same as Green Stuff?
Can I use super glue as a filler?
How long does Green Stuff take to cure?
What do I use to smooth putty?
More in Model Kit Tools for Gunpla and Scale Models, or start from the beginning with what to buy first.
Sources
- The Army Painter — Green Stuff (Kneadatite) product listingchecked November 2026
- Green Stuff World — Green Stuff tape formats and 100 g barchecked November 2026
- Milliput — Superfine White specification (113.4 g pack, 130 C, sets underwater)checked November 2026
- Tamiya USA — Putty (Basic Type) 87053, including the large-gap limitationchecked November 2026
- Miniature Market — Vallejo Plastic Putty 70.400, 17 ml dropper bottlechecked November 2026
- Horizon Hobby — Deluxe Materials Perfect Plastic Putty BD-44, 40 mlchecked November 2026
- Gundam Planet — Mr. Hobby Mr. Dissolved Putty P119, 40 mlchecked November 2026
- Walmart — Aves Apoxie Sculpt 1/4 lb, two-part self-hardening compoundchecked November 2026
- Spellenwinkel — Citadel Liquid Green Stuff 12 ml listingchecked November 2026